Seeking to combine up your ring designs slightly? When you’ve been working with bezel set rings and wish to transfer on to a brand new venture, why not strive your hand at a prong setting? Whereas bezel settings are neat and simple to perform, a prong setting will showcase the stone much more, making it supreme for jewelry items the place the stone is the point of interest.
The great thing about prong settings is that they are often any form you want. What’s extra, you may repair your stone with as many prongs as you’re feeling needed – will you create a six prong setting? Or an eight? It’s fully as much as you.
Be taught: How you can make a prong setting from wire
Learn on to find how you can make a prong setting, in just a few easy steps.
Making a prong setting
For this instance, we’ll take a look at how you can make a six prong setting.
You will want:
- Soldering set
- Wire (in whichever fashion you favor)
- Gemstone of alternative
- Pickling resolution
- File
- Cutters and pliers
- Prong pusher
- Anvil
Step 1: Create a bounce ring
Place your stone on a flat floor and create a circle of wire across the widest half. When you’re pleased with the form, take away the wire and gently solder the ends collectively.
Learn: 9 DIY Sprayer Growth Package: How To Make A Growth Sprayer
It’s necessary to measure your wire (bounce ring) across the widest a part of the stone, as this may present the help for the prongs and stone as soon as accomplished. Want to avoid wasting time? You should use pre-made bounce rings as a faster solution to get began along with your prong setting venture.
Step 2: Minimize your prongs
Begin this step by measuring the peak of your stone and including slightly additional to the peak at which you’ll lower the wire on your prongs. For instance, in case your stone measures 5mm in peak, you must lower your prongs at approx. 9mm in peak. This can permit you loads of room to bend your prongs and safe your stone.
Step 3: Solder your prongs
Now it’s time to solder your prongs to the bounce ring. You might have already soldered your bounce ring closed, but when not, you should use the hole as a place to begin on your first prong.
Ensure that your prong ends are filed flat in order that they’ve a very good floor for soldering. Add your flux and gently solder, use a soldering choose if the solder strikes. Try to use onerous solder for the prongs and watch out with the soldering warmth because it may soften your wire. When completed, pickle.
Working in your soldering approach? Learn our step-by-step information to soldering for knowledgeable hints and ideas.
Step 4: Bending your prongs
Insert your gemstone into the bounce ring and mark the perimeters on every prong utilizing a felt tip pen (Sharpies work nicely, as they switch onto any materials).
Studying: How you can begin a fireplace in ‘Breath of the Wild’
Utilizing your jewelry pliers, grasp every prong and push the setting towards your anvil, whereas bending your prongs upwards right into a 90-degree angle.
Step 5: Solder to your ring
When you’re including your prong stone setting to a hoop immediately, be sure you file a flat part on the ring floor and solder fastidiously. Ensure you take away the stone earlier than doing this, because the solder may trigger pointless injury. Then pickle.
Step 6: Set your stone
Putting your stone contained in the 90-degree prongs, take your prong pusher and push them proper towards the stone, slowly however with slightly pressure. You don’t wish to by accident snap your prongs! Attempt pushing the prongs in a north, south, east and west order to keep away from placing an excessive amount of stress on one aspect of the stone. This may also assist to safe the stone.
Step 7: Trim your prongs
Utilizing your cutters, trim your prongs from the place they meet on the centre of the stone. If you wish to obtain a pointed form, use the reverse aspect of your cutters. You possibly can all the time file the prongs barely if you want.
All that’s left to do is polish your six prong ring and admire your handiwork! Making a prong setting will be difficult, however by following our seven easy steps you’ll be capable to create stunning prong stone settings on your personal assortment or your jewelry making enterprise.
If you need to strive your hand at making a bezel setting as a substitute, don’t overlook you may learn our information on how you can make a bezel setting for recommendation and a step-by-step tutorial.
Save this for later
Studying: How you can Get a Libra Man Again After Breakup (Make Him Remorse Shedding You)
Written by