How To Build a Doll Bunk Bed – Free 18 Doll Bed Plans

How To Build a Doll Bunk Bed – Free 18 Doll Bed Plans

How To Construct a Doll Bunk Mattress – Free 18 Doll Mattress Plans

This step-by-step woodworking venture is about tips on how to construct a doll bunk mattress. I had some 1x2s left from different initiatives so I believed some time about what ought to I exploit them for. Once I lastly selected constructing a bunk mattress for 18 inch dolls, I needed to design some plans in order that it this venture may be constructed by any particular person with primary woodworking abilities. And I feel I managed to create some free doll mattress plans which are easy sufficient for any particular person to construct one. My venture requires no pocket or pilot holes. all it’s a must to do is lower and joint parts with wooden and brad nails.

We suggest you to put money into one of the best supplies you possibly can afford. Due to this fact, you should purchase weather-resistant lumber, reminiscent of pine or cedar. All the time take correct measurements earlier than adjusting the scale of the parts on the correct measurement. Drill pilot holes trough the parts earlier than inserting the wooden screws, to stop the wooden from splitting. There are even concrete log holders on the market, however I personally like to point out you tips on how to construct a wooden fire log holder.

Study: Methods to make a barbie bunk mattress

Learn: DIY Piñata Costume

Constituted of this plan

Learn: DIY Piñata Costume

Learn: DIY Piñata Costume

It’s that simple to construct a doll mattress!

Learn: DIY Piñata Costume

Learn: DIY Piñata Costume

Constructing a bunk mattress

Learn: DIY Piñata Costume


  • A – 5 items of 1×2 lumber – 18 1/2″ lengthy LEGS
  • B – 4 piece of 1×2 lumber – 18″ lengthy, 2 items – 9 1/2″ lengthy 2xFRAME
  • C – 2 items of 1×2 lumber – 8″ lengthy STEPS
  • D – 5 items of 1×2 lumber – 9 1/2″ lengthy, 2 items – 18″ lengthy, 2 items – 12 1/4″ lengthy RAILS
  • E – 2 items of 1/4″ plywood – 8″x18″ 2xFLOOR
  • 2 piece of 1×2 lumber – 6′
  • 3 items of 1×2 lumber – 8′
  • 1 piece of 1/4″ plywood – 16″x18″
  • 100 items of 1 1/4″ brad nails
  • stain, glue, putty

Learn: DIY Piñata Costume


  • Security gloves, glasses, Miter noticed, jigsaw
  • Chalk line, tape measure, spirit degree, carpentry pencil
  • Drill equipment and drill bits

Learn: DIY Piñata Costume


  • One Weekend

Learn: DIY Piñata Costume

Learn: DIY Piñata Costume

Free 18 Inch Doll Mattress Plans

Assembling the facet rails

Lower the parts from 1×2 lumber and assemble the facet rails with glue and 1 1/4″ brad nails.

Assembling the doll bed frames

Assembling the doll mattress frames

Connect the perpendicular slats to the facet rails and lock all the pieces along with brad nails and glue.

Attaching the legs

Attaching the legs

Match the legs to the 18″ doll mattress. Be certain that the corners are sq. earlier than inserting the nails. Add glue to the joints for knowledgeable end result.

Fitting the rails to the top bed

Becoming the rails to the highest mattress

Match the 1×2 rails to the highest mattress body. Use nails and glue. Use a scrap piece of 1×2 lumber as spacer.

Fitting the bottom to the beds

Becoming the underside to the beds

Lower 2 items of 1/4″ plywood and match them to the underside of the mattress frames.

Fitting the steps

Becoming the steps

Match the steps for the ladder utilizing glue and 1 1/4″ brad nails.

How to build a doll bed

Methods to construct a doll mattress

As soon as the bunk mattress for the 18 inch dolls is prepared, all you might be left to do is care for the ending touches. Clean the sides totally with 120-220 grit sandpaper after which apply stain to reinforce the look of the wooden.

Learn: DIY Piñata Costume

Learn: DIY Piñata Costume

How To Construct a Doll Bunk Mattress – Free 18 Doll Mattress Plans


After printing the plans, I lower all of the parts on the proper measurement, utilizing my miter noticed. I used 1x2s for the entire venture, apart from the underside panels, that are made out of 1/4″ plywood. You may use a cease block, as there are a lot of repetitive cuts. The cease will show you how to get constant outcomes, which can make the meeting lots simpler.

Clean the sides with sandpaper after making the cuts, in any other case the joints gained’t be neat.


After reducing the primary parts, it’s time to begin the meeting. For this venture, I’ll use brad nails and glue, so that you don’t want a drill equipment in any respect. Principally, you may get the job completed with simply hand instruments: a noticed, a sand block and a hammer. There you’ve gotten it: a newbie pleasant venture that value me below 5 {dollars} to make and required some very primary instruments.


First, I assembled the facet rails for the mattress frames. I added glue on one fringe of the rails.


Subsequent, I hooked up the cleat that can assist the underside of the mattress frames. I used 1 1/4″ brad nails to safe the parts collectively, after aligning the sides and ensuring they had been flush. If you’re a newbie, you would possibly discover helpful to clamp the parts collectively earlier than inserting the nails.


After assembling the facet rails, I hooked up the perpendicular parts to finish the mattress body. However first, it’s essential add glue to the ends, as proven within the picture.


Align the sides and ensure the corners are sq. earlier than inserting the brad nails. Be certain that the gaps between the parts are minimal for knowledgeable end result.


The primary mattress body is accomplished. It was that easy! Time to make the second for the 18 doll bunk mattress.


I used the identical methods described above the construct the second mattress body. Keep in mind that the 2 frames must be equivalent. In any other case the doll bunk mattress gained’t have a neat look.


Lay the legs for the doll mattress on a degree floor and align the ends. Then, match the decrease mattress body into place and measure 2″ from the ends. Align the sides ensuring the corners are sq.. Use 1 1/4″ brad nails to lock the parts collectively.


Subsequent, match the highest mattress body to the legs, ensuring the sides are align in knowledgeable method. Add glue to the joints and insert 1 1/4″ nails to reinforce the bond of the parts.


Connect the 1×2 legs to the alternative facet of the mattress frames. Be sure to take correct measurements earlier than inserting the nails, for knowledgeable end result.


Final however not least, match the assist for the ladder. You should use a clamp to carry the parts locked collectively when you insert the brad nails. You may simply alter the width of the ladder to fit your tastes. Truly, the 18 doll bunk mattress plans are absolutely customizable.


Match the 1×2 slats to the headboard and to the footboard of the highest mattress body. I used a chunk of 1×2 lumber as spacer, so I get constant gaps. Align the sides earlier than inserting the ending nails.


Learn: 16 Methods to Make an Additional 100 to 1000 a Month: How Reddit Customers Earn Money on the Aspect

Repeat the method for the footboard, ensuring all the pieces is aligned and completely sq..


As you may see within the picture, the venture is beginning to take form properly. Only a few extra steps until the doll mattress body is completed and prepared for stain.


Subsequent, I hooked up the 1×2 rails to the highest mattress body. As within the earlier steps, I used glue and 1 1/4″ brad nails to safe the parts to the helps. As well as, I used 1×2 lumber to area the rails in knowledgeable method.


Match the rails to the alternative facet, as effectively.


Now, I can actually see this doll mattress beginning to seem like the one I’ve envisioned. As alongside as you permit no gaps between the parts and also you align the sides flush, you should not have any issues constructing this venture in a day.


Match the steps to the ladder helps. As you may simply discover within the diagram, you possibly can use scrap items of 1×2 lumber as spacers. As well as, use glue and 1 1/4″ brad nails to safe the steps into place.


Subsequent, I lower two items of 1/4″ plywood and match them to the mattress frames. I haven’t used nails or glue to safe the items of plywood into place.


Now that the doll bunk mattress is lastly assembled, I’ll sand the sides with 120-220 grit sandpaper. As well as, you’ll fill the holes with wooden putty and let it harden for just a few hours, earlier than sanding the floor with high quality grit sandpaper.


Then, I took the mattress to my yard patio, so I can apply a coat of stain to the picket parts. After the stain dried, I utilized a coat of spray lacquer to seal all the pieces.


I’m tremendous pleased with how this venture got here off and I plan on construct much more, as presents. The one thinks that I might add are the mattresses and the pillows, so I make it look extra real looking. That is undoubtedly on my to do checklist. These little particulars may make the distinction between a “thanks” and a “IT’S AWESOME”.


Learn: DIY Piñata Costume


Learn: DIY Piñata Costume


All in all, I like this 5 $ venture because it makes for a tremendous current. Even when I don’t have enjoying with the dolls in my behavior, I nonetheless love the bunk mattress, as it’s a pretty-accurate scale mannequin.

Good Tip: Don’t neglect to share your initiatives with me, as I like seeing what you guys are engaged on. Ship me the pics HERE.

Learn: DIY Piñata Costume

Get PDF Plans

Learn: DIY Piñata Costume

Thanks for studying our venture about tips on how to construct a doll bunk mattress and we suggest you to take a look at the remainder of the initiatives. Don’t neglect to LIKE and SHARE our initiatives with your folks, by utilizing the social media widgets. SUBSCRIBE to be the primary that will get our newest initiatives.

Extra: Methods to Discover Clay in 7 Days To Die

Leave a Reply

Your email address will not be published. Required fields are marked *